My Blog
日々の生活を好き勝手につづったブログ（My blog is written by inoshita.jp）
メニュー
ファームセットアップログ
Orion1 CPU = Low
Checking DATA BUS
Checking ADDRESS BUS
> Checking hardware info ...
=== Strap status : 0x00800030 ===
=== H/W boardId : 0x23 ===
=== boardId : 0x1b ===
=== micon_support: off ===
> OK.
=== BUFFALO LS-HGL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (May 27 2008 - 19:18:26) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.17-1.00
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x3a
buffalo_IsStopAtUbootStatus > MagicKey=0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Writing 0x5c
Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD322HJ Firm: 1AC01113 Ser#: S17AJ1KQC01815
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Using device ide0, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 0
Using device ide0, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 0
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 1
Lost all init_rd
func switch pushed, and exited loop
wait until func switch released.
Marvell Serial ATA Adapter
Integrated Sata device found
Using device ide0, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 0
Using device ide0, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 0
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 3 2 1 0
Using egiga0 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'uImage.buffalo'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########
done
Bytes transferred = 1715900 (1a2ebc hex)
Using egiga0 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'initrd.buffalo'.
Load address: 0x800000
Loading: *#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############################################################
done
Bytes transferred = 5969136 (5b14f0 hex)
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-12-27 4:21:16 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1715836 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-12-27 4:23:28 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5969072 Bytes = 5.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.17 tftpboot=yes
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSHGL ---
Uncompressing Linux................................................................................................................ done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@build.dd-hot24.nas.buffalo.local) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #131 Sat Dec 27 13:21:07 JST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.17 tftpboot=yes
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110720KB available (2912K code, 550K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 1a
Flash bankwidth 1, base ff800000, size 40000
BUFFALO LS_HGL FLASH size 256[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_HGL
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011434)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
Vendor: SAMSUNG Model: HD322HJ Rev: 1AC0
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c142fba0
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda:
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 40000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.01 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Thu Nov 1 00:00:00 JST 2007
Thu Nov 1 00:00:00 JST 2007
CheckDevices
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
Starting :fsck_disks(boot) ... [Failed. ]
Starting :fsck_disks(rootfs) ... [Success.]
Starting :mount(boot) ... [Failed. ]
mount: you must specify the filesystem type
mount: you must specify the filesystem type
Freeing init memory: 108K
init started: BusyBox v1.1.1 (2008.12.27-02:40+0000) multi-call binary
Starting pid 377, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
chmod: /home: No such file or directory
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
swapon: /dev/sda5: No such device or address
create dir : /home
create dir : /var/www
umount: /boot: not mounted
mkdir: Cannot create directory `/boot': File exists
mount: you must specify the filesystem type
configure files from Buffalo parameters.
mount: you must specify the filesystem type
Restore previous configuration files
/bin/tar: /boot/conf_save.tgz: Cannot open: No such file or directory
/bin/tar: Error is not recoverable: exiting now
/bin/tar: Child returned status 2
/bin/tar: Error exit delayed from previous errors
/bin/tar: /boot/conf_save.tgz: Cannot open: No such file or directory
/bin/tar: Error is not recoverable: exiting now
/bin/tar: Child returned status 2
/bin/tar: Error exit delayed from previous errors
unzip fail.
umount: /boot: not mounted
rootfs on / type rootfs (rw)
/dev/root.old on / type ext2 (rw,nogrpid)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
PID Uid VmSize Stat Command
1 root 564 S init
2 root SWN [ksoftirqd/0]
3 root SW< [events/0]
4 root SW< [khelper]
5 root SW< [kthread]
11 root SW< [kblockd/0]
37 root SW [pdflush]
38 root SW [pdflush]
40 root SW< [aio/0]
39 root SW [kswapd0]
41 root SW< [xfslogd/0]
42 root SW< [xfsdatad/0]
43 root SW [crypto]
44 root SW [crypto_ret]
167 root SW< [scsi_eh_0]
168 root SW< [scsi_eh_1]
177 root SW [mtdblockd]
376 root 228 S init
377 root 656 S /bin/sh /etc/init.d/rcS
762 root 712 R /bin/sh /etc/init.d/restore_config.sh start
797 root 792 R ps
#[miconapl.usb_set_power]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new driver usbfs
/sbin/hotplug [drivers]
usbcore: registered new driver hub
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
/sbin/hotplug [usb_host]
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
usb usb1: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
/sbin/hotplug [usb_device]
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
/sbin/hotplug [usb_host]
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
usb usb2: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
/sbin/hotplug [usb_device]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
Initializing USB Mass Storage driver...
/sbin/hotplug [drivers]
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIface
alwaysFork
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
sendto: count 6 sync 1
sendto: count 5 sync 1
sendto: count 4 sync 1
sendto: count 3 sync 1
sendto: count 2 sync 1
sendto: count 1 sync 1
sendto: count 0 sync 1
dhcpInit call AutoipBound
setAutoIP eth0 called
MAC address = 00:1d:73:4f:b7:d9
file name /etc/dhcpc/autoip-eth0.info
/sbin/ifconfig eth0 169.254.5.196 netmask 255.255.0.0 up
Arp result 0
/etc/init.d/rService
** networking.sh dhcp fin.
add default if
configure files from Buffalo parameters.
Starting kernelmon:Starting clientUtil_server:starting on eth0
Starting daemonwatch:daemonwatch Ver.1.01
watch list file : /etc/daemonwatch.list
KERNELMOn (PSW_on)
No need to run drivecheck.sh
#[miconapl.boot_end]
KERNELMOn (lanact 0 half)
/etc/init.d/bootcomplete.sh: /etc/init.d/bootcomplete.sh: 46: /usr/lStarting pid 1167, console /dev/ttyS0: '/sbin/getty'
KERNELMOn (lanact 100 full)
**** request DHCP
BUFFALO INC. LinkStation series LS-HGL(SUININ)
LS-HGL-EM7D9 login: eth0: link down
KERNELMOn (lanact 0 full)
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
KERNELMOn (lanact 100 full)
** networking.sh dhcp fin.
dev = /dev/sda
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda:
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda:
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 >
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 >
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
XFS mounting filesystem sda2
/sbin/hotplug [block]
Adding 1004020k swap on /dev/sda5. Priority:-1 extents:1 across:1004020k
XFS mounting filesystem sda6
/sbin/hotplug [block]
Starting pid 1627, console /dev/ttyS0: '/etc/init.d/rcDown'
--- rcDown ---
===== exec:shutdown_start.sh =====
called shutdown_start /etc/init.d/shutdown_start.sh
#[miconapl.bz_on]
#[miconapl.shutdown_wait]
===== exec:shutdown_proc.sh =====
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 50: /etc/init.d/twonky.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 51: /etc/init.d/save_config.sh: not found
Stop daemonwatch:done.
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 53: /etc/init.d/logchkd.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 54: /etc/init.d/lsprcvd.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 55: /etc/init.d/cron.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 56: /etc/init.d/inetd.sh: not found
Stop errormon:killall: errormon: no process killed
done.
Stop clientUtil_server:rm: cannot remove `/var/run/clientUtil_server-eth0.pid': No such file or directory
$Shutting down FTPD services: killall: proftpd: no process killed
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 60: /etc/init.d/smb.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 61: /etc/init.d/atalk.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 62: /etc/init.d/bonjour.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 63: /etc/init.d/httpd.sh: not found
Deconfiguration network interface: lo eth0
cat: /var/run/diskmon.pid: No such file or directory
kill: usage: kill [-s sigspec | -n signum | -sigspec] [pid | job]... or kill -l [sigspec]
killall: diskmon_exec.sh: no process killed
Stop kernelmon:killall: /proc/buffalo/kernevnt: no process killed
done.
$Shutting down kernel logger: killall: klogd: no process killed
$Shutting down system logger: killall: syslogd: no process killed
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 68: /etc/init.d/modules.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 69: /etc/init.d/itunes.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 70: /etc/init.d/lprng.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 71: /etc/init.d/directcopy.sh: not found
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 72: /etc/init.d/ltbootd.sh: not found
#[miconapl.fan_set_speed]
cat: /var/run/miconmon.pid: No such file or directory
/usr/local/sbin/miconmon_exec.sh: kill: 110: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or
kill -l [exitstatus]
killall: miconmon_exec.sh: no process killed
Stop errormon:killall: errormon: no process killed
done.
cat: /var/run/pmcd.pid: No such file or directory
kill: usage: kill [-s sigspec | -n signum | -sigspec] [pid | job]... or kill -l [sigspec]
killall: pmcd_exec.sh: no process killed
/etc/init.d/shutdown_proc.sh: /etc/init.d/shutdown_proc.sh: 76: /etc/init.d/ups.sh: not found
===== exec:umount_disk.sh =====
killing all servers..
/etc/init.d/umount_disk.sh: /etc/init.d/umount_disk.sh: 4: /etc/init.d/smb.sh: not found
$Shutting down FTPD services: killall: proftpd: no process killed
/etc/init.d/umount_disk.sh: /etc/init.d/umount_disk.sh: 4: /etc/init.d/atalk.sh: not found
killing all daemons
Stop daemonwatch:done.
cat: /var/run/diskmon.pid: No such file or directory
kill: usage: kill [-s sigspec | -n signum | -sigspec] [pid | job]... or kill -l [sigspec]
killall: diskmon_exec.sh: no process killed
#[miconapl.fan_set_speed]
cat: /var/run/miconmon.pid: No such file or directory
/usr/local/sbin/miconmon_exec.sh: kill: 110: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or
kill -l [exitstatus]
killall: miconmon_exec.sh: no process killed
killall: rsync: no process killed
/etc/init.d/umount_disk.sh: /etc/init.d/umount_disk.sh: 4: /etc/init.d/httpd.sh: not found
killall: sshd: no process killed
\n==== unmounting all disks ====
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
/sbin/hotplug [block]
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
/sbin/hotplug [block]
===== exec:sendsigs.sh =====
swapoff: /dev/sda5: Invalid argument
$Shutting down kernel logger: killall: klogd: no process killed
$Shutting down system logger: killall: syslogd: no process killed
umount: /proc: device is busy
umount: /proc: device is busy
===== exec:errormon.sh =====
Stop errormon:killall: errormon: no process killed
done.
Starting pid 1988, console /dev/ttyS0: '/bin/umount'
The system is goiSending SIGKILL to all processes.
Please stand by while rebooting the system.
Synchronizing SCSI cache for disk sda:
Restarting system.
.
BuffaloChangePowerStatusBeforeHalt > Check power status. MagicKey = 24
BuffaloChangePowerStatusBeforeHalt > Changed to 43 from 24
Orion1 CPU = Low
Checking DATA BUS
Checking ADDRESS BUS
> Checking hardware info ...
=== Strap status : 0x00800030 ===
=== H/W boardId : 0x23 ===
=== boardId : 0x1b ===
=== micon_support: off ===
> OK.
=== BUFFALO LS-HGL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (May 27 2008 - 19:18:26) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.17-1.00
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x2b
buffalo_IsStopAtUbootStatus > MagicKey=0x2b
buffalo_change_power_status > Read 0x2b
buffalo_change_power_status > Read 0x2b
buffalo_change_power_status > Writing 0x5c
Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD322HJ Firm: 1AC01113 Ser#: S17AJ1KQC01815
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
1715900 bytes read
Image Name: Linux-2.6.16.16-arm1
Created: 2008-12-27 4:21:16 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1715836 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/initrd.buffalo
5969136 bytes read
Image Name: initrd
Created: 2008-12-27 4:23:28 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5969072 Bytes = 5.7 MB
Load Address: 00000000
Entry Point: 00000000
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD322HJ Firm: 1AC01113 Ser#: S17AJ1KQC01815
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
1715900 bytes read
Using device ide1, partition 1
** Bad partition 1 **
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-12-27 4:21:16 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1715836 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-12-27 4:23:28 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5969072 Bytes = 5.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.17
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSHGL ---
Uncompressing Linux................................................................................................................ done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@build.dd-hot24.nas.buffalo.local) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #131 Sat Dec 27 13:21:07 JST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.17
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110720KB available (2912K code, 550K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 1a
Flash bankwidth 1, base ff800000, size 40000
BUFFALO LS_HGL FLASH size 256[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_HGL
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011434)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
Vendor: SAMSUNG Model: HD322HJ Rev: 1AC0
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c142fba0
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 40000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.01 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Thu Nov 1 00:07:43 JST 2007
CheckDevices
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
Starting :fsck_disks(boot) ... [Failed. ]
Starting :fsck_disks(rootfs) ... XFS mounting filesystem sda2
/sbin/hotplug [block]
/sbin/hotplug [block]
[Success.]
Starting :mount(boot) ... kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
[Success.]
/sbin/hotplug [block]
** has Updated Files **
** Creating system hotadd pending flag **
Freeing init memory: 108K
init started: BusyBox v1.1.1 (2008.12.27-02:40+0000) multi-call binary
Starting pid 404, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
chmod: /home: No such file or directory
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 1004020k swap on /dev/sda5. Priority:-1 extents:1 across:1004020k
create dir : /home
create dir : /var/www
umount: /boot: not mounted
mkdir: Cannot create directory `/boot': File exists
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
exist [u-boot.buffalo.updated]
updating boot...
fwupdate.sh:FW update start
#[miconapl.boot_end]
#[miconapl.led_set_code_information]
Core Driver (ERROR) 0 0: Ignore Serror in response flags
Core Driver (ERROR) 0 0: Recoverable HW error detected.
Core Driver (ERROR) 0 0: SerrIntRecoverable error detected.
Core Driver (ERROR) SStatus 0x00000123:
Core Driver (ERROR) SControl 0x00000300:
Core Driver (ERROR) SError 0x00180000:
Core Driver (ERROR) IF Ctrl 0x00000000: TXPort 0x0
Core Driver (ERROR) IF status 0x00404034: RXFIS 0x34 RXPort 0x0
Core Driver (ERROR) 0 0: Clear Serror register(0x180000).
Linux IAL (ERROR) [0 0] sata recoverable error occured
mv: unable to rename `/boot/u-boot.buffalo': No such file or directory
exist [hddrootfs.buffalo.updated]
mkdir: Cannot create directory `/rootfs': File exists
Core Driver (ERROR) 0 0: Ignore Serror in response flags
Core Driver (ERROR) 0 0: Recoverable HW error detected.
Core Driver (ERROR) 0 0: SerrIntRecoverable error detected.
Core Driver (ERROR) SStatus 0x00000123:
Core Driver (ERROR) SControl 0x00000300:
Core Driver (ERROR) SError 0x00180000:
Core Driver (ERROR) IF Ctrl 0x00000000: TXPort 0x0
Core Driver (ERROR) IF status 0x00404034: RXFIS 0x34 RXPort 0x0
Core Driver (ERROR) 0 0: Clear Serror register(0x180000).
Linux IAL (ERROR) [0 0] sata recoverable error occured
Core Driver (ERROR) 0 0: Ignore Serror in response flags
Core Driver (ERROR) 0 0: Recoverable HW error detected.
Core Driver (ERROR) 0 0: SerrIntRecoverable error detected.
Core Driver (ERROR) SStatus 0x00000123:
Core Driver (ERROR) SControl 0x00000300:
Core Driver (ERROR) SError 0x00000000:
Core Driver (ERROR) IF Ctrl 0x00000000: TXPort 0x0
Core Driver (ERROR) IF status 0x00404034: RXFIS 0x34 RXPort 0x0
Core Driver (ERROR) 0 0: Clear Serror register(0x00).
Linux IAL (ERROR) [0 0] sata recoverable error occured
1000+0 records in
1000+0 records out
meta-data=/dev/sda2 isize=256 agcount=8, agsize=156383 blks
= sectsz=512
data = bsize=4096 blocks=1251061, imaxpct=25
= sunit=0 swidth=0 blks, unwritten=1
naming =version 2 bsize=4096
log =internal log bsize=4096 blocks=2560, version=1
= sectsz=512 sunit=0 blks
realtime =none extsz=65536 blocks=0, rtextents=0
format sda2 success.
XFS mounting filesystem sda2
/sbin/hotplug [block]
uncompressing tar image...
/sbin/hotplug [block]
XFS mounting filesystem sda2
/sbin/hotplug [block]
/sbin/hotplug [block]
rm: cannot remove `/boot/hddrootfs.buffalo.updated.done': No such file or directory
#[miconapl.led_set_code_information]
/sbin/hotplug [block]
Starting pid 856, console /dev/ttyS0: '/etc/init.d/rcDown'
Starting pid 1199, console /dev/ttyS0: '/bin/umount'
warning: can't open /etc/mtab: No sucThe system is going down NOW !!
Sending SIGTERM to all processes.
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
Synchronizing SCSI cache for disk sda:
Restarting system.
.
BuffaloChangePowerStatusBeforeHalt > Check power status. MagicKey = 24
BuffaloChangePowerStatusBeforeHalt > Changed to 43 from 24
Orion1 CPU = Low
Checking DATA BUS
Checking ADDRESS BUS
> Checking hardware info ...
=== Strap status : 0x00800030 ===
=== H/W boardId : 0x23 ===
=== boardId : 0x1b ===
=== micon_support: off ===
> OK.
=== BUFFALO LS-HGL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (May 27 2008 - 19:18:26) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.17-1.00
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x2b
buffalo_IsStopAtUbootStatus > MagicKey=0x2b
buffalo_change_power_status > Read 0x2b
buffalo_change_power_status > Read 0x2b
buffalo_change_power_status > Writing 0x5c
Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD322HJ Firm: 1AC01113 Ser#: S17AJ1KQC01815
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
1715900 bytes read
Image Name: Linux-2.6.16.16-arm1
Created: 2008-12-27 4:21:16 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1715836 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/initrd.buffalo
5969136 bytes read
Image Name: initrd
Created: 2008-12-27 4:23:28 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5969072 Bytes = 5.7 MB
Load Address: 00000000
Entry Point: 00000000
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD322HJ Firm: 1AC01113 Ser#: S17AJ1KQC01815
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
1715900 bytes read
Using device ide1, partition 1
** Bad partition 1 **
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-12-27 4:21:16 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1715836 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-12-27 4:23:28 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5969072 Bytes = 5.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.17
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSHGL ---
Uncompressing Linux................................................................................................................ done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@build.dd-hot24.nas.buffalo.local) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #131 Sat Dec 27 13:21:07 JST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.17
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110720KB available (2912K code, 550K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 1a
Flash bankwidth 1, base ff800000, size 40000
BUFFALO LS_HGL FLASH size 256[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_HGL
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011434)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
Vendor: SAMSUNG Model: HD322HJ Rev: 1AC0
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c142fba0
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 40000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.01 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Thu Nov 1 00:10:39 JST 2007
CheckDevices
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
Starting :fsck_disks(boot) ... [Success.]
Starting :fsck_disks(rootfs) ... XFS mounting filesystem sda2
/sbin/hotplug [block]
/sbin/hotplug [block]
[Success.]
Starting :mount(boot) ... kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
[Success.]
Starting :umount(boot) ... /sbin/hotplug [block]
[Success.]
XFS mounting filesystem sda2
/sbin/hotplug [block]
PRODUCTID=0x0000000E PRODUCTID=0x0000000E
KERNEL:2008/12/27 13:20:8
HDD:2008/12/27 13:25:20
KERNEL:2008/12/27 13:22:43
HDD:2008/12/27 13:25:20
-- CopyFromInitrdToHdd --
.........Finish
/sbin/hotplug [block]
XFS mounting filesystem sda2
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 108K
init started: BusyBox v1.1.1 (2008.12.27-02:40+0000) multi-call binary
Starting pid 537, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (hddroot) ---
Thu Nov 1 00:10:56 JST 2007
umount: /etc/pwrmgr: not mounted
* Starting /etc/rc.d/sysinit.d/S10checkroot.sh ...
mount: mount point /proc/bus/usb/ does not exist
mount: /dev/pts already mounted or /dev/pts busy
mount: according to mtab, devpts is already mounted on /dev/pts
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 1004020k swap on /dev/sda5. Priority:-1 extents:1 across:1004020k
[ ok ]
* Starting /etc/rc.d/sysinit.d/S11sethostname.sh ...
configure files from Buffalo parameters.
[ ok ]
* Starting /etc/rc.d/sysinit.d/S12restore_config.sh ...
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
Restore previous configuration files
/bin/tar: /boot/conf_save.tgz: Cannot open: No such file or directory
/bin/tar: Error is not recoverable: exiting now
/bin/tar: Child returned status 2
/bin/tar: Error exit delayed from previous errors
delete unnecessary samba lock files on //etc/samba/lock...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S20EnablingAutoip.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S20kernelmon.sh ...
Starting kernelmon: [ ok ]
* Starting /etc/rc.d/sysinit.d/S20miconmon.sh ...
#[miconapl.usb_set_power]
#[miconapl.fan_set_speed]
[ ok ]
* Starting /etc/rc.d/sysinit.d/S20usb.sh ...
#[miconapl.usb_set_power]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new driver usbfs
/sbin/hotplug [drivers]
usbcore: registered new driver hub
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
/sbin/hotplug [usb_host]
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
usb usb1: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
/sbin/hotplug [usb_device]
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
/sbin/hotplug [usb_host]
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
usb usb2: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
/sbin/hotplug [usb_device]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
Initializing USB Mass Storage driver...
/sbin/hotplug [drivers]
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ ok ]
* Starting /etc/rc.d/sysinit.d/S21hotplug.sh ...
KERNELMOn (PSW_on)
ls: /proc/scsi/usb-storage/: No such file or directory
[ ok ]
* Starting /etc/rc.d/sysinit.d/S21networking.sh ...
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIfaceeth0: link down
alwaysFork
KERNELMOn (lanact 0 half)
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
KERNELMOn (lanact 100 full)
sendto: count 6 sync 0
: already running
sendto: count 6 sync 0
dhcpInit call AutoipBound
setAutoIP eth0 called
MAC address = 00:1d:73:4f:b7:d9
file name /etc/dhcpc/autoip-eth0.info
/sbin/ifconfig eth0 169.254.38.198 netmask 255.255.0.0 up
Arp result 0
/etc/init.d/rService
** networking.sh dhcp fin.
add default if
configure files from Buffalo parameters.
[ ok ]
* Starting /etc/rc.d/sysinit.d/S21syslog.sh ...
Starting system logger:
Starting kernel logger:
[ ok ]
* Starting /etc/rc.d/sysinit.d/S22inetd.sh ...
Starting inetd: [ ok ]
* Starting /etc/rc.d/sysinit.d/S22mount_share.sh ...
XFS mounting filesystem sda6
/sbin/hotplug [block]
share
[ ok ]
* Starting /etc/rc.d/sysinit.d/S30diskmon.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S30drivecheck.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31atalk.sh ...
atalk is OFF
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31bonjour.sh ...
Starting Bonjour services: done
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31clientUtil_servd.sh ...
Starting clientUtil_server:starting on eth0
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31daemonwatch.sh ...
Starting daemonwatch:daemonwatch Ver.1.01
watch list file : /etc/daemonwatch.list
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31ftpd.sh ...
ftp is OFF
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31httpd.sh ...
start
Starting HTTPD services: /usr/local/apache/bin/apachectl start: httpd started
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31logrotate_init.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S31lsprcvd.sh ...
Starting lsprcvd: [ ok ]
* Starting /etc/rc.d/sysinit.d/S31smb.sh ...
/dev/sda6 /mnt/disk1 xfs rw 0 0
1229 : Warn! adding a admin/guest smbpasswd!
account_policy_get: tdb_fetch_uint32 failed for field 1 (min password length), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 2 (password history), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 3 (user must logon to change password), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 4 (maximum password age), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 5 (minimum password age), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 6 (lockout duration), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 7 (reset count minutes), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 8 (bad lockout attempt), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 9 (disconnect time), returning 0
account_policy_get: tdb_fetch_uint32 failed for field 10 (refuse machine password change), returning 0
Added user admin.
Added user guest.
configure samba
optarg:samba
LoadConfFileString:key=[local_auth] not found in /etc/melco/info.
load_info ItemValue = off
LoadConfFileString:key=[ad_dns] not found in /etc/melco/info.
LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info.
LoadConfFileString:key=[msdfs_link1_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link2_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link3_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link4_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link5_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link6_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link7_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link8_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link9_name] not found in /etc/melco/msdfs.
Can't Open : /etc/melco/shareinfo.hidden
Can't Open : /etc/melco/shareinfo.vfs
file:/etc/samba/smb.conf
>IconvCodeCharset CodePage=0,charset=CP932
file:/etc/pam_smb.conf
Setting up msdfs symbolic links... [Failed ]
Starting SMB services:
Starting NMB services:
[ ok ]
* Starting /etc/rc.d/sysinit.d/S32checkconfig.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S32cron.sh ...
Start services: crond [ ok ]
* Starting /etc/rc.d/sysinit.d/S32pwrmgr.sh ...
Starting pwrmgr:
Shutting down pwrmgr:
Starting pwrmgr:
[ ok ]
* Starting /etc/rc.d/sysinit.d/S32ups.sh ...
#[miconapl.ups_linefail_off]
#[miconapl.ups_shutdown_on]
[ ok ]
* Starting /etc/rc.d/sysinit.d/S40itunes.sh ...
[ !! ]
* Starting /etc/rc.d/sysinit.d/S40lprng.sh ...
Printer 'lp@localhost' - cannot open connection - No such file or directory
Make sure the remote host supports the LPD protocol
Printer 'lp-ps@localhost' - cannot open connection - No such file or directory
Make sure the remote host supports the LPD protocol
Start services: lpd
[ ok ]
* Starting /etc/rc.d/sysinit.d/S40ltbootd.sh ...
Starting services: rarpd tftpd rarpcfgd fwupdated.
[ ok ]
* Starting /etc/rc.d/sysinit.d/S40modules.sh ...
Starting module subsystem ...
Starting module webaxs ... [Success.]
[ ok ]
* Starting /etc/rc.d/sysinit.d/S40pmcd.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S40twonky.sh ...
TwonkyMedia Version 4.4.8
LOG_SYSTEM: reading ini file: "/usr/local/twonky/twonkymedia-default.ini".
/dev/sda6 /mnt/disk1 xfs rw 0 0
/mnt/disk1/share%HOSTNAME%: LinkStationjp [ ok ]
* Starting /etc/rc.d/sysinit.d/S50bootcomplete.sh ...
#[miconapl.boot_end]
[ ok ]
* Starting /etc/rc.d/sysinit.d/S51hdd_late_check.sh ...
[ ok ]
* Starting /etc/rc.d/sysinit.d/S52check_initialization.sh ...
[ ok ]
Starting pid 1694, console /dev/ttyS0: '/sbin/getty'
BUFFALO INC. LinkStation series LS-HGL(SUININ)
LS-HGL7D9 login: